#Azure point to site vpn route based how to
#Azure point to site vpn route based update

$subnet = Get-AzureRmVirtualNetworkSubnetConfig -Name GatewaySubnet -VirtualNetwork $vnet $vnet = Get-AzureRmVirtualNetwork -Name myVNet01 -ResourceGroupName myGroup Use the following example to create gateway configuration: The gateway configuration defines the subnet and the public IP address to use. New-AzureRmLocalNetworkGateway -Name LocalGW -ResourceGroupName myGroup -Location EastUS -GatewayIpAddress 112.33.44.44 -AddressPrefix 172.16.10.0/24 Create the gateway IP addressing configuration: To add a local network gateway with a single address prefix:

The AddressPrefix is on-premises address space.

VPN device cannot be located behind a NAT.

The GatewayIPAddress is the IP address of on-premises VPN device.

#Azure point to site vpn route based update

If our on-premises network changes, we can easily update the prefixes. The address prefixes we specify are the prefixes located on our on-premises network. We also specify the IP address prefixes that will be routed through the VPN gateway to the VPN device. We give the site a name by which Azure can refer to it, then specify the IP address of the on-premises VPN device to which we will create a connection. The local network gateway typically refers to our on-premises location. New-AzureRmPublicIpAddress -Name VNet01GWPIP -ResourceGroupName myGroup -Location EastUS -AllocationMethod Dynamic Use the following cmd to request a public IP address: The next step is to create a Public IP which must be dynamicallyДЄllocated to VPN gateway that we have created for our virtual network. Get-AzureRmVirtualNetworkSubnetConfig -Name GatewaySubnet -VirtualNetwork $vnet To Check if GatewaySubnet has been created successfully type $VirNet = Add-AzureRmVirtualNetworkSubnetConfig -Name GatewaySubnet -AddressPrefix 10.10.90.0/27 -VirtualNetwork $vnet $vnet = Get-AzureRmVirtualNetwork -ResourceGroupName myGroup -Name myVNet01 Use the following cmd to add a gateway subnet: I have already create Resource Group, Vnet, Subnet and a VM by following these articles in Power Shell SectionДЄfter creating above things, next step is to add Gateway Subnet that will contain the reserved IP addresses that the virtual network gateway services use. Shared key: For this example, i will use But, you can use whatever is compatible with your VPN hardware.The important thing is that the values match on both sides of the connection. You can use these values to create a test environment. I will use following values as an example. None of the subnets of your on-premises network can over lap with the virtual network subnets that you want to connect to. When you create this configuration, you must specify the IP address range prefixes that Azure will route to your on-premises location.Verify that you have an externally facing public IPv4 address for your VPN device.Microsoft Azure does not support all VPN devices so please make sure you have a compatible VPN device as per this article: About VPN Devices.

Please consider following points before creating S2S VPN:

#Azure point to site vpn route based how to

article shows you how to create a Site-to-Site VPN gateway connection from your on-premises network Firewall Netscreen SSG140 to the Azure VNet.ДЄ Site-to-Site VPN gateway connection is used to connect your on-premises network to an Azure virtual network over an IPsec/IKE (IKEv1 or IKEv2) VPN tunnel. Still doesn't work.ДЇounder and Principal Consultant - Richard M. Just for good measure I tried creating a route table with the VPN client subnet with the next hop as the virtual gateway and assigning it to the gateway subnet. My thinking here is the /24 is divided between the nodes as /25's. If I connect and get an address of 172.21.12.130 it fails. I'm assuming it is the second node because I've allocated the 172.21.12.0/24 subnet for VPN clients. It appears only to happen when I'm connected to the second node. Oddly, this does not happen every time I connect. Switching back to standard mode restores on-premises connectivity. The VPN gateway fails to route traffic to any on-premises networks reachable via the site-to-site link. However, when I enableДЄctive-active mode I can only reach resources in Azure. When I connect to the VPN with a client, I can access resources in Azure and on-premises via a site-to-site VPN connection configured on the same gateway. I have configured a route-based Azure VPN gateway (VpnGw1 SKU) in standard mode.